If you are getting the error message STATUS_WAIT_2 with code 0x80070002 when trying to create a system image backup using System Restore in Windows 10, this article should help you. In this article, we will identify the possible causes and suggest suitable solutions to help you solve the problem.
What causes the system restore error code “STATUS_WAIT_2”?
Corruption in personal subordinate files: The most common cause of this error code is a corrupted system recovery utility.
System recovery failure: Keep in mind that system recovery for Windows 10 is no longer supported or under development, and Microsoft will probably not include this utility in future releases because competitors have better products.
Windows 10 crash: This bug appeared to be caused by a strange Windows 10 crash that creates a permanent guest account (DefaultUser0) that the backup utility uses instead of the active account (with administrator access).
Operating system corruption: In some cases, this error message appears due to severe damage to the operating system that cannot be repaired with the included utilities.
How can I fix the system recovery error code ‘STATUS_WAIT_2’?
One of the most common problems in Windows 10 is the ‘sound enhancement problem’. Especially right after upgrading from a previous version of Windows. If you have encountered this problem, you are not alone. More importantly, the problem is usually pretty easy to fix.
Here are three simple solutions you can try. You don’t have to try them all. Just start at the top of the list and work your way down.
What is causing the “sound enhancement problem”?
The error message “Windows has detected that sound enhancement for the following device is causing problems” occurs, as everyone knows when the operating system detects multiple new sound output devices. This behavior occurs mainly because the previously configured sound enhancement is not compatible with the new device. This is a known bug in Windows 10 builds that lacks the Fall Creator’s Update.read more
Spotify users often report that they sometimes get a Spotify 3 error code. Although this is a common problem, there are many ways to fix this error caused by an incorrect username or password. In the following section, you’ll find a step-by-step list of how to fix the Spotify 3 error code once and for all.
What causes a Spotify 3 error code?
The problem is often caused by a password error, possibly when changes were made to the password requirements for Spotify. This can easily be fixed by resetting the Spotify password. In addition, users have reported that they were able to fix the problem simply by using their Spotify username instead of their email or vice versa.read more
Spotify is one of the best music streaming services on the market, especially if you like obscure artists. On the other hand, nothing ruins music faster than frequent pauses and buffering. This is a common Spotify problem that has many causes, but the good news is that they’re all easily fixable.
If Spotify is constantly pausing and interrupting your listening, here’s what to do.
What are the causes for the “Spotify Keeps Pausing” problem?read more
Are you looking for a PC backup and restore solution that is reliable and easy to use? If so, then you may want to consider Restoro. This software has been gaining in popularity over the past few years, and for good reason. It is one of the most comprehensive backup and restore solutions on the market today. In this article, we will take a closer look at what Restoro has to offer, and see if it is the right solution for you.
How safe is Restoro?
The internet is full of software programs that claim to be able to repair your computer. Many of these programs are scams, but some, like Restoro, are legitimate. So, is Restoro safe?read more
If you are running Windows and see the error message “Intel ICD OpenGL driver name cannot be found”, you are not alone. Many Windows users report this problem. But the good news is that you can easily solve this problem yourself by following these instructions.
This problem is mainly caused by an old version of your Intel video card driver. You can solve this problem by updating your video card driver.
What causes the “Intel ICD OpenGL driver name not found”?
In most cases, the problem occurs after the user has upgraded from an older version to Windows 10. In some cases, an incompatible Intel HD driver is installed during the upgrade, which causes this error.
This error can also occur if you try to open an application designed to run on 32-bit systems on a 64-bit computer. The same is true in the opposite case, although it is much less likely.
How to eliminate the “Intel ICD OpenGL driver name not found” message?
Whether you’re using a Windows operating system or not, you may still encounter frightening “blue screen of death” (BSOD) errors. Your system displays them when it fails to deal with a critical problem, to make sure you understand the severity of the situation. This is the case with IaStorA.sys BSOD, which occurs when something goes wrong with your IaStorA.sys driver and causes your PC to crash.
A loud crackling or popping noise from the speakers or headphones can be annoying and indicate that something is wrong with the system. It is usually the result of connection problems – often caused by poor quality cables. Sizzling, crackling, noise, and sound problems can occur for many reasons, and we recommend that you check your equipment.
In this guide, we’ll go over some steps to resolve these problems. Remember that there are many possible causes for these problems. So try the methods below to find a solution for your system.read more
ShowBox is one of the most popular streaming apps because of its excellent user interface. Despite such great success, the app faces some problems as it continues to evolve. If ShowBox isn’t working, you’ve encountered one of the most common problems with Showbox. Note that these errors are caused by different factors and can be resolved in different ways.
If you are trying to fix the ShowBox application, you must first determine the nature of the problem. This troubleshooting guide will help you do that.read more
If your computer is infected with malware or a virus, this can cause Windows Defender to be disabled. It is also possible that Windows Defender is automatically disabled after you install anti-virus software. In this case, you will get the following error message when you open Windows Defender:
“This application is disabled by Group Policy. In order for this application to work, contact your security administrator to enable the program via Group Policy.
What causes the Windows Defender error ‘This application is disabled by Group Policy’ message?
A virus has infiltrated your computer.
You accidentally disabled it.
If a domain controller disabled it.
You installed incompatible antivirus software.
How do I fix the Windows Defender error ‘This application is disabled by Group Policy’ notification?
Activate Windows Defender in settings
Open settings and select Update and Security to continue.
Select Windows Security and then click on Virus and Threat Protection under the Protection Zones option to continue.
In the window that opens, click Virus and Threat Protection Settings to continue.
Find the Real-time Protection section, turn it on, and click Yes.
Change group policy settings
Press the Win and R keys together to open the Run and Continue dialog box.
Type gpedit.MSC in the box and click OK to continue.
In the Local Group Policy Editor, go to Local Computer Policy -> Administrative Templates -> Windows
Components -> Windows Defender Antivirus to continue.
In the right pane, double-click Disable Windows Defender Antivirus to open a new window.
Select Disabled and click Apply and OK to save your changes.
Enable Windows Defender service
Press the Win and R keys together to open the Run box to continue.
Type services.MSC and click OK to continue.
In the window that opens, find the Windows Defender Antivirus service and double-click it to select properties, and continue.
In the new window, select the General tab, set the startup type to Automatic, and then click Startup under Service Status.
Then click Apply and OK to save your settings.
Using the Registry Editor
Press the Win and R keys together to open the Run field to continue.
Type Regedit in the box, then click OK and Yes to continue.
In the window that appears, locate the Windows Defender folder at Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows Defender to continue.
Right-click DisableAntiSpy (type points to REG_DWORD) and select Delete.